Kein Zugriff auf SCSI-Geräte
Verfasst: So 20. Jul 2014, 16:15
Nach Einbau eines Motherboards durch eine Firma kommt es zu einem
Abbruch des Zugriffs auf SCSI-Geräte. Nach Beheben einiger Stärungen
komme ich aber jetzt nicht weiter.
Betriebssystem: OS/2 Warp 4 englisch mit "Internal Revision 14.088_W4
Motherboard: GA-M55plus-S3G von Gigabyte
SCSI-Controller: Adaptec 19160 Version 2.57.2
Im Boot Menü (über Alt-F1) erhate ich:
1. für F2 : The system is stopped. Correct the preceding error and restart the Sytem.
2. für F4 : "internal processing error at location ##0168: ff1eb1c - 000e: cb 1c
3. für F5: OS/2 is unable to operate your hard disk or diskette drive
4. für F6: ebenso wie unter F5
Offensichtlich komme ich aber mit der Startoption unter der Partition C: in die CONFIG.SYS.
Denn dort wird die Funktion "SCSI Disk Sleeper" version 0.98 vom 27. Februar 2001 aufgerufen
und es kommt zu folgender Fehlermeldung:
DSLEEP$ : no devices found
OS/2 is unable to operate your hard disk or diskette drive. The system ist stopped. Correct
the preceding error and restart the system.
Die Test-Prozedur des SCSO-Controllers Adaptec SCSI Card 19160 führt den Scan der
SCSI-Geärte korrekt für alle IDs durch und meldet mit korrekten Name:
(nur diie IDs für die installierten Geräte:
ID#0 : IBM DNES..... (Festplatte) und Boot-Platte
ID#1: IBM DGHS..... (Festplatte)
ID#4: IBM DNES... (Festplatte)
ID#5: IBM DVRM (DVD-Laufwewrk)
ID#7: Adaptec SCSI Card 19160
Unter Configuretion beim SCSI Controller ist gesetzt:
Host Adaptec SCSI ...... 7
SCSI Parity Checking..... Enabled
Host Adatec Termination
LVD/SE Connector .....Automatic
Fast-Ultra-SE Connector .....Automatic
Boot SCSI ID ......0
Boot LUN Number .......0
BIOS Information:
Interrupt (IRQ) Channel .... 11
I/O Port Address ......A000h
SCSI Termination Level ...... 1
Die Reihenfolge der SCSI-Geräte nach dem Anschluss des Breitbandkabels
ist (reiendolge der IDs der Geräte - siehe oben): 4, 1, 0 und 5
Wenn ich im Menü des Adaptec-Controlllers unter "Boot device Options"
das "BOOt SCSI ID" von 0 auf 1 setzen will, bleibt das ohne Erfolg. d.h.
ich kann die "=" nicht per Tastatur auf "1" setzen.
Für weiterreichende Tipps und Hinweise wäre ich dankbar.
Abbruch des Zugriffs auf SCSI-Geräte. Nach Beheben einiger Stärungen
komme ich aber jetzt nicht weiter.
Betriebssystem: OS/2 Warp 4 englisch mit "Internal Revision 14.088_W4
Motherboard: GA-M55plus-S3G von Gigabyte
SCSI-Controller: Adaptec 19160 Version 2.57.2
Im Boot Menü (über Alt-F1) erhate ich:
1. für F2 : The system is stopped. Correct the preceding error and restart the Sytem.
2. für F4 : "internal processing error at location ##0168: ff1eb1c - 000e: cb 1c
3. für F5: OS/2 is unable to operate your hard disk or diskette drive
4. für F6: ebenso wie unter F5
Offensichtlich komme ich aber mit der Startoption unter der Partition C: in die CONFIG.SYS.
Denn dort wird die Funktion "SCSI Disk Sleeper" version 0.98 vom 27. Februar 2001 aufgerufen
und es kommt zu folgender Fehlermeldung:
DSLEEP$ : no devices found
OS/2 is unable to operate your hard disk or diskette drive. The system ist stopped. Correct
the preceding error and restart the system.
Die Test-Prozedur des SCSO-Controllers Adaptec SCSI Card 19160 führt den Scan der
SCSI-Geärte korrekt für alle IDs durch und meldet mit korrekten Name:
(nur diie IDs für die installierten Geräte:
ID#0 : IBM DNES..... (Festplatte) und Boot-Platte
ID#1: IBM DGHS..... (Festplatte)
ID#4: IBM DNES... (Festplatte)
ID#5: IBM DVRM (DVD-Laufwewrk)
ID#7: Adaptec SCSI Card 19160
Unter Configuretion beim SCSI Controller ist gesetzt:
Host Adaptec SCSI ...... 7
SCSI Parity Checking..... Enabled
Host Adatec Termination
LVD/SE Connector .....Automatic
Fast-Ultra-SE Connector .....Automatic
Boot SCSI ID ......0
Boot LUN Number .......0
BIOS Information:
Interrupt (IRQ) Channel .... 11
I/O Port Address ......A000h
SCSI Termination Level ...... 1
Die Reihenfolge der SCSI-Geräte nach dem Anschluss des Breitbandkabels
ist (reiendolge der IDs der Geräte - siehe oben): 4, 1, 0 und 5
Wenn ich im Menü des Adaptec-Controlllers unter "Boot device Options"
das "BOOt SCSI ID" von 0 auf 1 setzen will, bleibt das ohne Erfolg. d.h.
ich kann die "=" nicht per Tastatur auf "1" setzen.
Für weiterreichende Tipps und Hinweise wäre ich dankbar.